4/3/2023 0 Comments Digital performer 8 tutorials![]() In this case, we have a Clarett 8PreX connected with an Internal Clock Source selected and a Sample Rate of 44.1 kHz: Below is where you will set your Sample Rate and Clock Source.įor more information on Clock Source and Sample Rate: Click Hereįor more information on which Clock Source to choose: Click Here Remote Devices (not shown) - If you want to control Focusrite Control remotely using Focusrite Control for iOS, compatible devices will show up here for enabling.įollowing down on the left side of the software the next bubble down will show you which unit you have connected as well as which firmware is installed on your device.Talkback - This allows you to choose the Talkback mic's Source as well as control the talkback mic's input level.Rename box - This allows you to rename your inputs up to 11 characters.Monitor Controls (*applicable only to select devices) - Set which outputs the 'MONITOR' knob on the front panel will control.Speaker Switching - This allows you to enable single button switching between output pairs 1-2 and 3-4.Retain 48V - This allows you to control if the phantom power option is on by default when the unit is power cycled.Digital I/O Mode or S/PDIF Source - This allows you to choose the digital inputs and formats you are using, more information can be found in the relevant user guide for your specific product.Sample Rate, Clock Source, Sync Status - These controls indicate how the unit is in sync, either with your DAW (which should be automatic) or with external equipment connected via digital inputs/outputs on the interface (e.g.By default, this will display the manufacturing identification number. Hardware ID - Each unit can be renamed to identify two or more of the same interface.Pad - When Pad is engaged, your input signal will be reduced by -10dB when being sent you your DAW.For more information please see this video. AIR - This setting modifies the input's frequency response, giving a lift in the treble frequencies.For more information on Mic, Line, and Instrument level click here Line/Inst - Switch to either 'Line' or 'Instrument' level/impedance depending on your source type.Focusrite Control version - Here you can see the Focusrite Control version you are using and, if needed, update to the latest version on our downloads page.Input Settings/Output Routing - This allows you to view your Input Settings or Output Routing tab.Talk - This allows you to toggle Talkback on/off.Main Alt - Indicates, and when clicked, allows you to change between two monitor pairs by routing audio to Main Outputs 1-2 or Alt Outputs 3-4 (Scarlett 18i8 3rd Gen/18i20 3rd Gen).Settings tab - This allows you to show or hide the left-hand settings pane. ![]() Sync Light - This light should be green indicating the unit is in 'Sync' with itself or external devices when lit Red the unit will not pass audio.For clarification, please see your products user guide here: This tab will show you settings related to the interface's mic, instrument and line inputs and how they have been configured.īelow, each section is defined and their functions explained, note some functions are specific to certain devices. We have also created a video on Focusrite Control here: This is the setting used for the following explanations. If at any point you are lost, in the top left corner of the screen you will see File > Restore Factory Defaults. If Focusrite Control details "/ Controls are not supported on this device", this is normal and any controls relating to this will be on the physical unit itself.A Clarett 8PreX & Scarlett 18i20 3rd generation have been used for this article.Functionality is different for each unit.In addition to this article, you can find range-specific Focusrite Control User Guides on all relevant product download pages here. This software gives you a user-friendly control surface to set the routing and recording parameters of your unit, as well as input settings. Applies To: Scarlett 2 nd Generation 6i6, 18i8, & 18i20 Scarlett 3rd Generation and Clarett Range.įocusrite Control is the software necessary to make changes in your Focusrite hardware.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |